Discussion:
acm3200 wifi problems
(too old to reply)
Reinoud Koornstra
2018-03-11 01:23:40 UTC
Permalink
Hi Everyone,

I did build an image forthe acm3200, but it does have wifi problems.

Linux version 4.14.25 (***@router-dev) (gcc version 7.3.0 (OpenWrt
GCC 7.3.0 r6420-4e8f1e9f4c)) #0 SMP Sat Mar 10 10:58:19 2018

Please see below, did anyone else see this?

[ 8.632226] <<Marvell Mac80211 Wireless PCIE Network Driver version
10.3.4.0-20180226>>
[ 8.640291] pci 0000:00:01.0: enabling device (0140 -> 0142)
[ 8.646071] ieee80211 phy0: priv->pcmd_buf = de248000
priv->pphys_cmd_buf = 1e248000
[ 8.699213] ieee80211 phy0: fw download start
[ 8.699218] ieee80211 phy0: ddr init: download start
[ 8.699595] ieee80211 phy0: ddr init: download complete
[ 8.837306] ieee80211 phy0: FwSize = 450512 downloaded Size =
450512 curr_iteration 65522
[ 11.709190] ieee80211 phy0: fw download complete
[ 11.709218] ieee80211 phy0: device node: /soc/pcie/***@1,0
[ 11.724587] ieee80211 phy0: pcmd = de248000
[ 11.742629] ieee80211 phy0: firmware version: 0x9030205
[ 12.103212] ieee80211 phy0: firmware region code: 10
[ 12.134797] ieee80211 phy0: 2G disabled, 5G enabled
[ 12.139712] ieee80211 phy0: 4 TX antennas, 4 RX antennas
[ 12.145175] pci 0000:00:02.0: enabling device (0140 -> 0142)
[ 12.150981] ieee80211 phy1: priv->pcmd_buf = d9e9c000
priv->pphys_cmd_buf = 19e9c000
[ 12.158518] ieee80211 phy1: fw download start
[ 12.158523] ieee80211 phy1: ddr init: download start
[ 12.158908] ieee80211 phy1: ddr init: download complete
[ 12.300381] ieee80211 phy1: FwSize = 450512 downloaded Size =
450512 curr_iteration 65527
[ 13.495197] ieee80211 phy1: fw download complete
[ 13.495243] ieee80211 phy1: device node: /soc/pcie/***@2,0
[ 13.510657] ieee80211 phy1: pcmd = d9e9c000
[ 13.528214] ieee80211 phy1: firmware version: 0x9030205
[ 13.888199] ieee80211 phy1: firmware region code: 10
[ 13.911809] ieee80211 phy1: 2G enabled, 5G disabled
[ 13.916711] ieee80211 phy1: 4 TX antennas, 4 RX antennas

However, it isn't happy at all.

[ 17.255416] ieee80211 phy0: change: 0x100
[ 17.264214] ieee80211 phy0: change: 0x60
[ 17.309628] ieee80211 phy1: change: 0x100
[ 17.318217] ieee80211 phy1: change: 0x42
[ 17.465219] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 17.482624] ieee80211 phy0: change: 0x40
[ 17.699202] ieee80211 phy0: change: 0x60
[ 17.797216] ieee80211 phy0: change: 0x100
[ 17.851427] ieee80211 phy0: change: 0x100
[ 17.859194] ieee80211 phy0: change: 0x62
[ 18.024206] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 26.466483] ieee80211 phy1: staid 1 deleted
[ 35.029038] ieee80211 phy1: staid 1 deleted
[ 36.438466] ieee80211 phy0: staid 1 deleted
[ 38.837777] ieee80211 phy0: staid 1 deleted
[ 39.819456] ieee80211 phy0: staid 1 deleted
[ 41.645183] ieee80211 phy1: staid 1 deleted
[ 48.539349] ieee80211 phy1: staid 1 deleted
[ 49.469574] ieee80211 phy1: staid 1 deleted
[ 62.347371] ieee80211 phy1: staid 1 deleted
[ 66.269491] ieee80211 phy1: staid 1 deleted

Loading...